Recommended Options settings

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Curt C
    1000 Post Veteran

    • Jul 2001
    • 1032
    • UP's dead Santa Barbara Sub
    • General
    #1

    Recommended Options settings

    Some time ago, there was a discussion on the recommended/suggested settings for Options in OR. After years of operating both MSTS and OR with an older computer, I opted to upgrade the entire system, and am now ready to set the Options for better performance. I've read the Manual for the latest 1.4 release, but would like to get some ideas as to what others are doing. As mentioned, the earlier discussion on this subject, covered a lot of helpful info, but I am unable to locate the archived thread.
    Thanks in advance,

    Curt
    Tags: None
    • trainmanaustin
      Senior Member
      • Oct 2004
      • 126
      • Helena, MT
      #2
      Kind of depends on the computer hardware that you have.

      Sent from my SM-G988U using Tapatalk

        Comment

        • Curt C
          1000 Post Veteran

          • Jul 2001
          • 1032
          • UP's dead Santa Barbara Sub
          • General
          #3
          Sorry for being vague. I'm not a computer-guy, and I'm still exploring and learning with this new system. I'm now running Windows 10, with a AMD Ryzen 3 1200 Quad-Core Processor; 32 GB, and a AMD Radeon RX 5500 XT graphics card. Hope that's enough info.

            Comment

            • trainmanaustin
              Senior Member
              • Oct 2004
              • 126
              • Helena, MT
              #4
              My system is about 6 years old now and these are the settings that I run. You may ask why I have the "Level of detail bias" at 99% and not 100%. I found that I would loose as much as 10FPS when moving to 100% from 99% and I have not been able to see what detail is missing at 99% versus 100%.

              Sent from my SM-G988U using Tapatalk

                Comment

                • R. Steele
                  3500 Post Veteran

                  • Feb 2013
                  • 3928
                  • known universe
                  • ORTS
                  #5
                  Originally posted by trainmanaustin
                  My system is about 6 years old now and these are the settings that I run. You may ask why I have the "Level of detail bias" at 99% and not 100%. I found that I would loose as much as 10FPS when moving to 100% from 99% and I have not been able to see what detail is missing at 99% versus 100%...
                  You may want to try setting the level of detail bias slider to the default of zero...take a look at the explanation of this setting from the manual:

                  6.10.14 Level of detail bias
                  Many visual objects are modelled at more than one level of detail (LOD) so, when they are seen at a distance, Open Rails can switch to the lesser level of detail without compromising the view. This use of multiple LODs reduces the processing load and so may increase frame rates.
                  Lowering the LOD Bias setting below 0 reduces the distance at which a lower level of detail comes into view, and so boosts frame rates but there may be some loss of sharpness.
                  Raising the LOD Bias setting above 0 increases the distance at which a lower level of detail comes into view. This may be useful to sharpen distant content that was created for a smaller screen or a wider field of view than you are currently using.
                  If your content does not use multiple LODs, then this option will have no effect.
                  Originally posted by Curt C
                  ... I've read the Manual for the latest 1.4 release, but would like to get some ideas as to what others are doing...
                  Curt
                  Curt, "dynamic shadows" and "shadow all shapes" will affect FPS, not familiar with AMD cards, but you can probably check those boxes. Try starting with "Run at 32 bit on Win64" Options/General Tab unchecked, and see what happens, you've got enough memory to handle that.

                  You really don't need over 60FPS to run any route in OR --- so if your Ryzen card is powerful enough you can check "Vertical Sync" on the video tab. I running a Nvidia RTX 2070 and have no problems running any route at 60fps. I've got the Anti-Aliasing slider set to 4xMSAA. routes look good to me. The Mullan route ( newest built specifically for OR ) looks and runs very well, no flashing foliage, weird shimmering, etc...a lot of the video problems one sees in the older routes just do not appear.

                  You'll have to experiment until you find the settings that work for your rig.
                  Last edited by R. Steele; 01-07-2022, 20:14.
                  Cheers, Gerry
                  "A mind is like a parachute. It doesn't work if it is not open." Frank Zappa
                  It's my railroad and I'll do what I want! Historically accurate attitude of US Railroad Barons.
                  Forever, ridin' drag in railroad knowledge.
                  Audi, Vide, Tace, Si Vis Vivere In Pace​

                  https://www.trainsim.com/forums/filedata/fetch?filedataid=79656&type=medium​ https://www.trainsim.com/forums/filedata/fetch?filedataid=79654&type=small

                    Comment

                    • trainmanaustin
                      Senior Member
                      • Oct 2004
                      • 126
                      • Helena, MT
                      #6
                      Originally posted by R. Steele
                      You may want to try setting the level of detail bias slider to the default of zero...take a look at the explanation of this setting from the manual:





                      Curt, "dynamic shadows" and "shadow all shapes" will affect FPS, not familiar with AMD cards, but you can probably check those boxes. Try starting with "Run at 32 bit on Win64" Options/General Tab unchecked, and see what happens, you've got enough memory to handle that.

                      You really don't need over 60FPS to run any route in OR --- so if your Ryzen card is powerful enough you can check "Vertical Sync" on the video tab. I running a Nvidia RTX 2070 and have no problems running any route at 60fps. I've got the Anti-Aliasing slider set to 4xMSAA. routes look good to me. The Mullan route ( newest built specifically for OR ) looks and runs very well, no flashing foliage, weird shimmering, etc...a lot of the video problems one sees in the older routes just do not appear.

                      You'll have to experiment until you find the settings that work for your rig.
                      Ok, I just realized that I was still using the 1.3 manual and not the latest version. Thank you for pointing this out to me.

                      Sent from my SM-G988U using Tapatalk

                        Comment

                        Previous template Next
                        Working...

                          We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We do not share information about our users with anyone. For additional details, refer to our Privacy Policy.

                          By clicking "I UNDERSTAND" below, you consent to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                          I Understand