Problem in TSRE5 with NEC 4

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Don6218
    1500 Post Veteran
    • Jun 2009
    • 1834
    • Oshawa ON

    #1

    Problem in TSRE5 with NEC 4

    Hello all. I am having an issue with TSRE5 / Open Rails. When running my train through this same area, all scenery (Tiles, I guess) are intact and present. When I go to the same area to change out the tractor that is shown, the base has disappeared! It will not allow placement of anything there. I can delete the tractor but I cannot replace it with an alternate.

    It seems only in this area as witnessed by the second shot.

    The route checks out fine in RR and operates normally. While using TSRE5 it also acts normal. Any suggestions?
    NEC 4 TSRE5 (A).jpg
    NEC 4 TSRE5 (B).jpg
  • Vince
    6500 Post Veteran

    • Nov 1999
    • 6961
    • Mohave

    #2

    I am having an issue with TSRE5 / Open Rails.
    Okay, issue with TSRE
    But further on you state this:
    While using TSRE5 it also acts normal.
    Oops! TSRE works normal does it???

    Have you looked at the TSRE log?

    regards,
    ............Vince ..............
    ...... Author NECv4 .......
    .... LIRR BUILD PHOTOS ....
    ...... Eschew Obsfucation ......

    On the The Statue of Liberty in New York Harbor there is a Tablet. On it is written:
    "Give me your tired, your poor, your huddled masses yearning to breathe free,
    the wretched refuse of your teeming shore, send these, the homeless, tempest-tossed to me,
    I lift my lamp beside the golden door!"

    Comment

    • GokuMK
      Senior Member

      • Oct 2015
      • 729
      • Poland

      #3
      Try to add this line in settings.txt:

      useQuadTree = false

      Comment

      • Don6218
        1500 Post Veteran
        • Jun 2009
        • 1834
        • Oshawa ON

        #4
        Originally posted by Vince

        Okay, issue with TSRE
        But further on you state this:
        Oops! TSRE works normal does it???

        Ok, by this I meant it works in that the CarSpawner is active and it shows partial scenery. Also it is only with NEC 4 Route. I tried opening others and no issues with missing terrain.

        Have you looked at the TSRE log?

        ??? Where do I find this "Log"?

        regards,
        Also, GokuMK, where do I find the "Main TSRE5" file to edit the settings?

        Thank you both for the information.

        Comment

        • longiron
          1000 Post Veteran and Moderator

          • Jan 2007
          • 1453
          • Just south of NYC

          #5
          In your main TSRE installation folder, you should have a file named settings.txt.
          Chris
          "True rail fans have two favorite railroads. The B&O and one other."

          Comment

          • Don6218
            1500 Post Veteran
            • Jun 2009
            • 1834
            • Oshawa ON

            #6
            My installation has that line with a (#) at the start.

            Comment

            • GokuMK
              Senior Member

              • Oct 2015
              • 729
              • Poland

              #7
              # means comment so the option is disabled.
              If this route uses simple 2x2 km terrain tiles then it should work good with QuadTree disabled. Open Rails doesn't use QT too.

              If the route uses custom terrain tile sizes, then QuadTree must be enabled. There is bug in TSRE QT implementation that causes some tiles to not load because TSRE thinks that the terrain tile isn't present in Quad Tree. And I think that is this case.

              Comment

              • Don6218
                1500 Post Veteran
                • Jun 2009
                • 1834
                • Oshawa ON

                #8
                Yes that corrected the issue. It works properly now, thank you very much.

                Comment

                Working...