Dynamic Brake Issue on Engine - No issue in MSTS

[qballbandit]

Hello,
Last night I was using an SD60 as my lead engine, and when needing to set the Dynamic braking, I couldn't get it to apply past "Setup". This tells me that the keystroke still recognizes it's command; to throw it into setup, but wouldn't increase any further.
I have no issues in MSTS with this .eng file and Dynamic braking. I am using combined throttle/dynamic control in the .eng file, for ease. My SD40-2's are set up the same way, and they have no issues.

Here is my throttle/brake section of the .eng file - any ideas??

EngineControllers (
Throttle ( 0 1 0.125 0
NumNotches ( 9
Notch ( 0 0 Dummy )
Notch ( 0.125 0 Dummy )
Notch ( 0.25 0 Dummy )
Notch ( 0.375 0 Dummy )
Notch ( 0.5 0 Dummy )
Notch ( 0.625 0 Dummy )
Notch ( 0.75 0 Dummy )
Notch ( 0.875 0 Dummy )
Notch ( 1 0 Dummy )
)
)
Brake_Engine ( 0 1 0.0250 1
NumNotches ( 1
Notch ( 0 1 Dummy )
)
)
Brake_Train ( 0 1 0.0125 0.4
NumNotches ( 5
Notch ( 0 0 TrainBrakesControllerReleaseStart )
Notch ( 0.3 1 TrainBrakesControllerGraduatedSelfLapLimitedHoldin gStart )
Notch ( 0.85 0 TrainBrakesControllerSuppressionStart )
Notch ( 0.9 0 TrainBrakesControllerContinuousServiceStart )
Notch ( 0.95 0 TrainBrakesControllerEmergencyStart )
)
)
Brake_Dynamic ( 0 1 0.0125 0
NumNotches ( 10
Notch ( 0 0 Dummy )
Notch ( 0.0125 1 Dummy )
Notch ( 0.022 1 Dummy )
Notch ( 0.033 1 Dummy )
Notch ( 0.044 1 Dummy )
Notch ( 0.055 1 Dummy )
Notch ( 0.066 1 Dummy )
Notch ( 0.077 1 Dummy )
Notch ( 0.088 1 Dummy )
Notch ( 1.0 1 Dummy )
)
)
Combined_Control( 0 1 0.5 0.5 throttle dynamic )
DirControl ( -1 0 1 1 )
BellToggle( 0 1 0 )
Sanding ( 0 1 0 )
Horn ( 0 1 0 )
EmergencyStopToggle( 0 1 0 )
Vigilance ( 0 1 0 )
Headlights ( 0 0.25 1 0 )
BailOffButton( 0 1 0 )
)

Thanks much!

[lineman]

Are the db parameters set up the same in the cab file?

[qballbandit]

Yes, I did that a ways back in MSTS for all my add-on cabs.
I wouldn't think it would have worked properly in MSTS if I had missed that, or flubbed up the edit?

[baldwin]

There is a built in delay in OR, to allow for the relays to set up for braking.

[qballbandit]

I understand the delay, but this particular engine never gets past "setup", where other engines function as expected.
I'll giver her another go this weekend, and see is she behaves differently - or if the delay, for whatever reason, is abnormally long in comparison to my other engines.